Please use this identifier to cite or link to this item: http://localhost/handle/Hannan/72082
Full metadata record
DC FieldValueLanguage
dc.date.accessioned2013en_US
dc.date.accessioned2020-04-06T06:18:14Z-
dc.date.available2020-04-06T06:18:14Z-
dc.date.issued2013en_US
dc.identifierASTM G75en_US
dc.identifier.govdocLGIZGFAAAAAAAAAAen_US
dc.identifier.urihttp://localhost/handle/Hannan/72082-
dc.descriptionen_US
dc.descriptionen_US
dc.description.abstractThis test method covers a single laboratory procedure that can be used to develop data from which either the relative abrasivity of any slurry (Miller Number) or the response of different materials to the abrasivity of different slurries (SAR Number), can be determined.&#160; <br>The test data obtained by this procedure is used to calculate either a number related to the rate of mass loss of duplicate standard-shaped 27 % chromium iron wear blocks when run for a period of time in the slurry of interest (Miller Number), or to calculate a number related to the rate of mass loss (converted to volume loss) of duplicate standard-shaped wear specimens of any material of interest when run for a period of time in any slurry of interest (SAR Number).&#160; <br>The requirement for a finished flat wearing surface on the test specimen for a SAR Number test may preclude application of the procedure where thin (0.051 to 0.127-mm), hard, wear-resistant coatings will not allow for surface finishing. The 6 hours total duration of the SAR Number Test may not allow establishment of a consistent rate-of-mass-loss of the unfinished surface.&#160; <br><em>This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.</em>en_US
dc.format.extent2007.08.15 (R 2013)en_US
dc.format.extent21en_US
dc.languageEnglishen_US
dc.relation.haspartLGIZGFAAAAAAAAAA.pdfen_US
dc.titleStandard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number)en_US
dc.typeStandarden_US
dc.journal.titleASTM - ASTM Internationalen_US
Appears in Collections:ASTM

Files in This Item:
File SizeFormat 
LGIZGFAAAAAAAAAA.pdf640.54 kBAdobe PDF
Full metadata record
DC FieldValueLanguage
dc.date.accessioned2013en_US
dc.date.accessioned2020-04-06T06:18:14Z-
dc.date.available2020-04-06T06:18:14Z-
dc.date.issued2013en_US
dc.identifierASTM G75en_US
dc.identifier.govdocLGIZGFAAAAAAAAAAen_US
dc.identifier.urihttp://localhost/handle/Hannan/72082-
dc.descriptionen_US
dc.descriptionen_US
dc.description.abstractThis test method covers a single laboratory procedure that can be used to develop data from which either the relative abrasivity of any slurry (Miller Number) or the response of different materials to the abrasivity of different slurries (SAR Number), can be determined.&#160; <br>The test data obtained by this procedure is used to calculate either a number related to the rate of mass loss of duplicate standard-shaped 27 % chromium iron wear blocks when run for a period of time in the slurry of interest (Miller Number), or to calculate a number related to the rate of mass loss (converted to volume loss) of duplicate standard-shaped wear specimens of any material of interest when run for a period of time in any slurry of interest (SAR Number).&#160; <br>The requirement for a finished flat wearing surface on the test specimen for a SAR Number test may preclude application of the procedure where thin (0.051 to 0.127-mm), hard, wear-resistant coatings will not allow for surface finishing. The 6 hours total duration of the SAR Number Test may not allow establishment of a consistent rate-of-mass-loss of the unfinished surface.&#160; <br><em>This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.</em>en_US
dc.format.extent2007.08.15 (R 2013)en_US
dc.format.extent21en_US
dc.languageEnglishen_US
dc.relation.haspartLGIZGFAAAAAAAAAA.pdfen_US
dc.titleStandard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number)en_US
dc.typeStandarden_US
dc.journal.titleASTM - ASTM Internationalen_US
Appears in Collections:ASTM

Files in This Item:
File SizeFormat 
LGIZGFAAAAAAAAAA.pdf640.54 kBAdobe PDF
Full metadata record
DC FieldValueLanguage
dc.date.accessioned2013en_US
dc.date.accessioned2020-04-06T06:18:14Z-
dc.date.available2020-04-06T06:18:14Z-
dc.date.issued2013en_US
dc.identifierASTM G75en_US
dc.identifier.govdocLGIZGFAAAAAAAAAAen_US
dc.identifier.urihttp://localhost/handle/Hannan/72082-
dc.descriptionen_US
dc.descriptionen_US
dc.description.abstractThis test method covers a single laboratory procedure that can be used to develop data from which either the relative abrasivity of any slurry (Miller Number) or the response of different materials to the abrasivity of different slurries (SAR Number), can be determined.&#160; <br>The test data obtained by this procedure is used to calculate either a number related to the rate of mass loss of duplicate standard-shaped 27 % chromium iron wear blocks when run for a period of time in the slurry of interest (Miller Number), or to calculate a number related to the rate of mass loss (converted to volume loss) of duplicate standard-shaped wear specimens of any material of interest when run for a period of time in any slurry of interest (SAR Number).&#160; <br>The requirement for a finished flat wearing surface on the test specimen for a SAR Number test may preclude application of the procedure where thin (0.051 to 0.127-mm), hard, wear-resistant coatings will not allow for surface finishing. The 6 hours total duration of the SAR Number Test may not allow establishment of a consistent rate-of-mass-loss of the unfinished surface.&#160; <br><em>This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.</em>en_US
dc.format.extent2007.08.15 (R 2013)en_US
dc.format.extent21en_US
dc.languageEnglishen_US
dc.relation.haspartLGIZGFAAAAAAAAAA.pdfen_US
dc.titleStandard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number)en_US
dc.typeStandarden_US
dc.journal.titleASTM - ASTM Internationalen_US
Appears in Collections:ASTM

Files in This Item:
File SizeFormat 
LGIZGFAAAAAAAAAA.pdf640.54 kBAdobe PDF